日韩不卡视频在线观看一区_亚洲国产精品久久久久久6p_区三区日韩免费毛片_亚洲精品久久一区二区三区四区_精品国产电影久久官网_婷婷五月天视频_久久久国产成人片_婬乱久久久久_伊人久久大香线蕉av蜜芽_不卡在线中文字幕av

歡迎進入濟南濟柴環能燃氣發電設備有限公司官網!

常見問題解答

天然氣發電機組啟動前后要注意哪些?

返回 2020.12.08 來源:http://m.pyucoin.com 0
一、天然氣發電機組啟動前的準備:啟動前先檢查調整好整個機組的狀況,各個組件的連接及固定須無誤,發動機的冷卻水系,電啟動系統都連接穩定,不滴漏、不松脫,開關靈活,潤滑系良好,燃氣供給系以及點火系都確認正常,否則要檢修、調整正確方可啟動。
1、 Preparation before start-up of natural gas generator set: check and adjust the condition of the whole unit before start-up. The connection and fixation of each component must be correct. The cooling water system of the engine and the electric starting system are connected stably without dripping and loosening. The switch is flexible. The lubrication system is in good condition. The fuel supply system and ignition system are confirmed to be normal. Otherwise, it can be started only after maintenance and adjustment are correct 。
二、啟動后的怠速運行:準備正常后,打開燃氣閥門,接上啟動電源,打開鑰匙,按下按鈕,-可啟動機組。當機組啟動后,注意機油壓力表,有正常的機油壓力,萬萬不可粗心大意。啟動后要怠速運行一段時間,一是用以觀察各處、各部件的運行情況是否異常,有無異常聲響,有問題處理、解決。怠速運轉也是用來使機器升溫,冬季,這升溫很重要,將利于機器的使用。
2、 Idle running after starting: after preparing for normal operation, open the gas valve, connect the starting power supply, open the key, and press the button, - the unit can be started. When the unit starts, pay attention to the oil pressure gauge, there is normal oil pressure, never be careless. If there is abnormal operation of each part, observe whether there is abnormal operation for a period of time. Idle running is also used to make the machine warm up. In winter, this temperature rise is very important, which will be conducive to the use of the machine.
沼氣發電機組
三、正常的負載輸出:當經怠速觀察,且機組已達到了溫度(觀察水溫表即可)就可以操縱電調“油門”將機組升速到標定的工作轉速,調整機組的電壓和頻率都達到標定值,則可向外界合閘,輸出負載。為了合閘時外界有負載使用,建議合閘前交將空車的轉速(頻率)稍稍偏高些。負載變化時,注意調速“油門”手柄,即電子調速器的電位器,適應輸出,使得電壓和頻率的穩定。
3、 Normal load output: when the idle speed is observed and the unit has reached the temperature (just observe the water temperature meter), the electric adjustment "throttle" can be operated to speed up the unit to the rated working speed, and the voltage and frequency of the unit are adjusted to reach the calibration value, then the machine can be switched on to the outside to output the load. In order to use the external load when closing, it is suggested that the speed (frequency) of the empty car be slightly higher before closing. When the load changes, pay attention to the speed control "throttle" handle, that is, the potentiometer of the electronic governor, to adapt to the output, so that the voltage and frequency are stable.
1、天然氣發電機組機房應遠離明火區域;
1. Natural gas generator room should be far away from open fire area;
2、機房應寬敞、明亮且要求安裝換氣扇以使得良好的通風;
2. The machine room should be spacious and bright, and the ventilator should be installed to ensure good ventilation;
3、發電機組安裝時底盤與地基應用平墊鐵找平。接觸面積應在60%以上,且分布均勻;
3. When the generator set is installed, the chassis and the foundation shall be leveled with flat pad iron. The contact area should be more than 60% and evenly distributed;
4、室內安裝照明、開關、線路及其電器應采用防爆措施,且固定牢;
4. Indoor installation of lighting, switches, lines and electrical appliances should adopt explosion-proof measures and be fixed firmly;
5、機房內應符合消防要求,配備滅火器等消防器械;
5. The machine room shall meet the fire fighting requirements and be equipped with fire extinguisher and other fire-fighting equipment;
6、天然氣發電機組機房內安裝可燃氣體報警裝置,可燃氣體泄露時能及時發現;
6. Combustible gas alarm device is installed in the machine room of natural gas generator set to detect the leakage of combustible gas in time;
7、60kw以下單臺燃氣發動機燃氣管路的外部主要管道內徑應不小于2吋,靠近發動機的部分內徑應不小于1吋!60kw以上燃氣發電機組則分別是3吋和兩吋。且須安裝燃氣閥門(不銹鋼球閥)、型放水閥、防回火裝置,燃氣管路焊接完成應清理焊渣(用高壓空氣);
7. The inner diameter of the outer main pipe of the gas pipeline of a single gas engine below 60kW shall not be less than 2 inches, and the inner diameter of the part close to the engine shall not be less than 1 inch! For gas-fired generating units above 60kW, they are 3 inches and 2 inches respectively. Gas valve (stainless steel ball valve), type-I drain valve and anti backfire device shall be installed. Welding slag (with high-pressure air) shall be cleaned after gas pipeline welding;
8、燃氣須脫硫、脫水、除塵,其中含流量≤0.25Nm3,氫氣≤10%;
8. The gas must be desulphurized, dehydrated and dedusted, with flow rate ≤ 0.25nm3 and hydrogen ≤ 10%;
9、發電機組冷卻水須用軟化水。
9. The cooling water of generator set must be softened water.
以上是小編分享的沼氣發電機組,你還見過哪些新穎有趣的知識嗎?,歡迎在點擊網站的鏈接http://m.pyucoin.com  ,在留言中寫下你要表達的內容.
The above is the biogas generating set shared by Xiaobian. What new and interesting knowledge have you seen? , welcome to click on the website link http://m.pyucoin.com   Write down what you want to say in the message
新聞搜索
濟南濟柴環能燃氣發電設備有限公司
  • 服務熱線

    0531-62325028
    0531-69951266

天然氣發電機組啟動前后要注意哪些?

一、天然氣發電機組啟動前的準備:啟動前先檢查調整好整個機組的狀況,各個組件的連接及固定須無誤,發動機的冷卻水系,電啟動系統都連接穩定,不滴漏、不松脫,開關靈活,潤滑系良好,燃氣供給系以及點火系都確認正常,否則要檢修、調整正確方可啟動。
1、 Preparation before start-up of natural gas generator set: check and adjust the condition of the whole unit before start-up. The connection and fixation of each component must be correct. The cooling water system of the engine and the electric starting system are connected stably without dripping and loosening. The switch is flexible. The lubrication system is in good condition. The fuel supply system and ignition system are confirmed to be normal. Otherwise, it can be started only after maintenance and adjustment are correct 。
二、啟動后的怠速運行:準備正常后,打開燃氣閥門,接上啟動電源,打開鑰匙,按下按鈕,-可啟動機組。當機組啟動后,注意機油壓力表,有正常的機油壓力,萬萬不可粗心大意。啟動后要怠速運行一段時間,一是用以觀察各處、各部件的運行情況是否異常,有無異常聲響,有問題處理、解決。怠速運轉也是用來使機器升溫,冬季,這升溫很重要,將利于機器的使用。
2、 Idle running after starting: after preparing for normal operation, open the gas valve, connect the starting power supply, open the key, and press the button, - the unit can be started. When the unit starts, pay attention to the oil pressure gauge, there is normal oil pressure, never be careless. If there is abnormal operation of each part, observe whether there is abnormal operation for a period of time. Idle running is also used to make the machine warm up. In winter, this temperature rise is very important, which will be conducive to the use of the machine.
沼氣發電機組
三、正常的負載輸出:當經怠速觀察,且機組已達到了溫度(觀察水溫表即可)就可以操縱電調“油門”將機組升速到標定的工作轉速,調整機組的電壓和頻率都達到標定值,則可向外界合閘,輸出負載。為了合閘時外界有負載使用,建議合閘前交將空車的轉速(頻率)稍稍偏高些。負載變化時,注意調速“油門”手柄,即電子調速器的電位器,適應輸出,使得電壓和頻率的穩定。
3、 Normal load output: when the idle speed is observed and the unit has reached the temperature (just observe the water temperature meter), the electric adjustment "throttle" can be operated to speed up the unit to the rated working speed, and the voltage and frequency of the unit are adjusted to reach the calibration value, then the machine can be switched on to the outside to output the load. In order to use the external load when closing, it is suggested that the speed (frequency) of the empty car be slightly higher before closing. When the load changes, pay attention to the speed control "throttle" handle, that is, the potentiometer of the electronic governor, to adapt to the output, so that the voltage and frequency are stable.
1、天然氣發電機組機房應遠離明火區域;
1. Natural gas generator room should be far away from open fire area;
2、機房應寬敞、明亮且要求安裝換氣扇以使得良好的通風;
2. The machine room should be spacious and bright, and the ventilator should be installed to ensure good ventilation;
3、發電機組安裝時底盤與地基應用平墊鐵找平。接觸面積應在60%以上,且分布均勻;
3. When the generator set is installed, the chassis and the foundation shall be leveled with flat pad iron. The contact area should be more than 60% and evenly distributed;
4、室內安裝照明、開關、線路及其電器應采用防爆措施,且固定牢;
4. Indoor installation of lighting, switches, lines and electrical appliances should adopt explosion-proof measures and be fixed firmly;
5、機房內應符合消防要求,配備滅火器等消防器械;
5. The machine room shall meet the fire fighting requirements and be equipped with fire extinguisher and other fire-fighting equipment;
6、天然氣發電機組機房內安裝可燃氣體報警裝置,可燃氣體泄露時能及時發現;
6. Combustible gas alarm device is installed in the machine room of natural gas generator set to detect the leakage of combustible gas in time;
7、60kw以下單臺燃氣發動機燃氣管路的外部主要管道內徑應不小于2吋,靠近發動機的部分內徑應不小于1吋!60kw以上燃氣發電機組則分別是3吋和兩吋。且須安裝燃氣閥門(不銹鋼球閥)、型放水閥、防回火裝置,燃氣管路焊接完成應清理焊渣(用高壓空氣);
7. The inner diameter of the outer main pipe of the gas pipeline of a single gas engine below 60kW shall not be less than 2 inches, and the inner diameter of the part close to the engine shall not be less than 1 inch! For gas-fired generating units above 60kW, they are 3 inches and 2 inches respectively. Gas valve (stainless steel ball valve), type-I drain valve and anti backfire device shall be installed. Welding slag (with high-pressure air) shall be cleaned after gas pipeline welding;
8、燃氣須脫硫、脫水、除塵,其中含流量≤0.25Nm3,氫氣≤10%;
8. The gas must be desulphurized, dehydrated and dedusted, with flow rate ≤ 0.25nm3 and hydrogen ≤ 10%;
9、發電機組冷卻水須用軟化水。
9. The cooling water of generator set must be softened water.
以上是小編分享的沼氣發電機組,你還見過哪些新穎有趣的知識嗎?,歡迎在點擊網站的鏈接http://m.pyucoin.com  ,在留言中寫下你要表達的內容.
The above is the biogas generating set shared by Xiaobian. What new and interesting knowledge have you seen? , welcome to click on the website link http://m.pyucoin.com   Write down what you want to say in the message
亚洲理伦| 色a在线| 国产人妻人伦| 99精品欧美一区二区三区综合在线| 91成人www| 色999亚洲| 国产成人无码综合亚洲AV| 91精品视频在线播放| 成人午夜视频精品一区| 国产偷拍av| 精品99网站| 熟女av网站| 国产黄色大片| 真实国产精品亲子伦视频对白| 亚洲熟妇无码久久精品爱| 8848成人网| 亚洲免费看97视频| 人妻激情在线77| 一区二区三区视频不卡| 91欧美| 日韩福利视频| 亚州国产成人精品女人久久久| 国产精品国产三级国产专业不| 免费99精品国产自在在线| 国产91免费观看| 亚洲第一第二第三区999av无码| 黄色性爱91免费网站| 免费国产一级aV片在线观看| 香蕉在线99热| 岛国操逼ta| 精品九九| 国产精品美女久久久久图片| 色九月婷婷| 午夜在线一区| 亚洲视频在线一区二区| 成人免费毛片| 中文字幕精品无码| 91精品人妻| 亚洲女人av久久天堂| 日韩一级毛卡片| 国产精品久久久久久无码五月蜜臂|