實際上受制于氣源以及使用環境的變化，瓦斯發電機組在使用過程中經常會出現故障，這些故障主要可分為：

In fact, due to the change of gas source and use environment, gas generator sets often have faults during use. These faults can be divided into:

1、氣源故障：瓦斯氣的濃度、流量過低,還有因瓦斯輸送管道上氣液分離器、干式阻火器堵塞造成氣體流通不暢,輸送管道漏氣等,機組供氣不足的現象統稱為氣源故障。

1. Gas source failure: the concentration and flow of gas are too low, the gas flow is blocked due to the blockage of gas-liquid separator and dry flame arrester on the gas transmission pipeline, and the transmission pipeline leaks. The phenomenon of insufficient gas supply of the unit is collectively referred to as gas source failure.

2、機組故障：機組故障主要包括機組本體零部件損壞。如潤滑系統漏油、進氣閥和排氣閥損壞等。

2. Unit failure: the unit failure mainly includes the damage of the unit body parts. Such as oil leakage of the lubricating system, damage of the inlet valve and exhaust valve, etc.

3、電氣故障：電氣故障主要包括點火系統不點、電壓低、二次線連接觸不良、開關損壞等。

3. Electrical fault: electrical fault mainly includes ignition system spotless, low voltage, poor contact of secondary line connection, switch damage, etc.

在上述三類故障中，其中尤以機組故障尤為突出，其約占總體故障的70％左右，且發生故障后，導致的后果為嚴重。

Among the above three types of failures, the unit failure is particularly prominent, accounting for about 70% of the total failures, and the consequences caused by the failure are serious.

啟動系統故障主要由以下原因造成：

The starting system failure is mainly caused by the following reasons:

1、啟動電磁閥是否良好,電流、電壓是否正常。由于電磁閥內接線空間較小,接線時很容易造成導線斷線,又不易被發現,運行一段時間由于導線或端子氧化等造成接觸不良,均會造成電磁閥無法啟動；

1. Check whether the starting solenoid valve is in good condition and whether the current and voltage are normal. Due to the small wiring space in the solenoid valve, it is easy to cause wire breakage during wiring, and it is not easy to be found. The solenoid valve cannot be started due to poor contact caused by oxidation of wires or terminals during operation for a period of time;

2、壓縮空氣壓力是否正常,空氣屏內是否有積水和雜質、臟物造成主啟動閥堵塞,無法開啟；

2. Whether the pressure of compressed air is normal, and whether there is water, impurities and dirt in the air screen that cause the main starting valve to be blocked and cannot be opened;

3、空氣分配器工作是否良好,由于機組運行時振動較大、油質較臟,空氣分配器內滑塊邊緣易磨損,造成密封不嚴漏氣,此時機組也會因啟動壓力不足,無法啟動。

3. Whether the air distributor works well. Due to the large vibration and dirty oil during the operation of the unit, the edge of the sliding block in the air distributor is easy to wear, resulting in poor sealing and air leakage. At this time, the unit cannot be started due to insufficient starting pressure.

因此，針對機組故障的實時監測，對故障的預警具有重要意義。您只有提前多去了解多去做預防措施，才能讓故障少出現，即便是出現了也能快速解決。關注我們http://m.pyucoin.com，了解更多！

Therefore, the real-time monitoring of unit faults is of great significance to the early warning of faults. Only if you know more in advance and take more preventive measures can you reduce the number of failures, and even if they occur, you can quickly solve them. Follow us http://m.pyucoin.com , learn more!