煙氣脫硝技術特點：SCR脫硝技術具有脫硝效率、適應當前環保要求等優點，受到電力行業的高度重視和廣泛應用。在環保要求嚴格的發達國家，如德國、日本、美國、加拿大、荷蘭、奧地利、瑞典、丹麥等國家，SCR脫硝技術已成為應用更廣泛、更成熟的技術之一。

Characteristics of flue gas denitration technology: SCR denitration technology has the advantages of denitrification efficiency and meets the current environmental protection requirements, and has been highly valued and widely used by the power industry. SCR denitration technology has become one of the most widely used and mature technologies in developed countries with strict environmental protection requirements, such as Germany, Japan, the United States, Canada, the Netherlands, Austria, Sweden, Denmark and other countries.

經過脫硝反應后再通過SCR反應器出口煙道回到空氣預熱器, 典型布置如圖2所示。典型高塵布置設計方式, 在SCR反應器入口和出口煙道均需設計排灰斗(特別是對于高粉塵煙氣), 這樣, 不但可以有效減小催化劑的磨損, 而且可以有效減輕空氣預熱器的堵塞和磨損, 同時也可以減少脫硝還原劑的消耗量,保證系統安全、穩定運行。

After denitrification, the flue at the outlet of SCR reactor is returned to the air preheater. The typical arrangement is shown in Fig. 2. The typical design mode of high dust arrangement requires the design of ash discharge hopper (especially for high dust flue gas) at the inlet and outlet flue of SCR reactor. In this way, not only the catalyst wear can be effectively reduced, but also the blockage and wear of air preheater can be effectively reduced, and the consumption of denitration reducing agent can be reduced, and the system can be safely and stably operated.

脫硝系統調試，脫硝系統調試是保證系統運行的穩定性、可靠性以及能否達到設計性能保證值更重要的工作之一。

The commissioning of denitration system is one of the most important tasks to ensure the stability, reliability and the design performance of the system.

催化劑砷中毒后，氨不易吸附到中毒的催化劑活性點上，從而導致催化劑活性的降低。在使用過程中可使催化劑表面對砷不具有活性

After arsenic poisoning, ammonia is not easily adsorbed to the active point of the catalyst, which leads to the decrease of catalyst activity. The catalyst surface can be inactive to arsenic during the use,

脫硝煙道灰斗，SCR法煙氣脫硝裝置的布置方式根據反應器布置位置的不同, 通常可分為高塵布置與低塵布置。高塵布置的SCR反應器通常布置在鍋爐省煤器與空氣預熱器之間, 受布置空間所限, SCR反應器不能直接布置在鍋爐省煤器下(立式鍋爐除外),而是煙氣通過水平煙道引出后再通過上升煙道連接SCR反應器,

The arrangement of ash hopper and SCR Flue gas denitration device can be divided into high dust arrangement and low dust arrangement according to the different arrangement position of reactor. SCR reactors with high dust arrangement are usually arranged between boiler economizer and air preheater. Restricted by the layout space, SCR reactors cannot be directly arranged under boiler economizer (except vertical boilers), but flue gas is led out through horizontal flue and connected to SCR reactor through rising flue,

根據發達國家的經驗，SCR脫硝技術必將成為我國火電廠燃煤鍋爐的主要脫硝技術，并得到越來越廣泛的應用。SCR法脫硝關鍵技術，工程上常用的、成熟的脫硝技術主要有低氮燃燒技術、SNCR法煙氣脫硝技術、SCR法煙氣脫硝技術, 本文僅針對工程上應用更多、脫硝效率高的SCR法煙氣脫硝技術進討。

According to the experience of developed countries, SCR denitrification technology will become the main denitrification technology of coal-fired boiler in thermal power plants in China, and it will be widely used. SCR denitrification key technology, commonly used in engineering, mature denitrification technology mainly includes low nitrogen combustion technology, SNCR flue gas denitrification technology, SCR Flue Gas Denitrification Technology, this paper only discusses SCR Flue gas denitration technology which has the most application in the project and high denitrification efficiency.

通過對催化劑表面的酸性控制，達到吸附保護的目的，使得催化劑表面不吸附氧化砷；另一種方法是改進活性位，通過高溫煅燒獲得穩定的催化劑表面，

The purpose of adsorption protection is achieved by controlling the acidity of catalyst surface, so that arsenic oxide is not adsorbed on the catalyst surface; another method is to improve the active position and obtain stable catalyst surface by calcination at high temperature,

著重在設計并制備高活性的催化劑上，改進催化劑的組成，提高活性，降低成本，提高催化劑壽命。催化劑在實際工程應用中，要通過合理的流場設計 ，瓦斯發電機scr脫硝

The design and preparation of high activity catalyst are emphasized, which can improve the composition of catalyst, improve the activity, reduce the cost and improve the catalyst life. In practical engineering application, catalyst should be denitrated by SCR of gas generator through reasonable flow field design

流場模擬試驗，進入反應器催化劑層入口的煙氣流場分布均勻與否直接影響脫硝系統的各項性能指標, 如果流場分布不均勻, 不但會嚴重影響脫硝效率、增加氨的逃逸、加速催化劑磨損, 嚴重時還會堵塞催化劑或引起空氣預熱器的堵塞和嚴重腐蝕, 從而影響主機的正常運行, 因此, 流場模擬試驗研究在脫硝系統設計中極為重要。

The flow field simulation test shows that the distribution of flue gas flow into the catalyst layer inlet of the reactor directly affects the performance indexes of denitration system. If the flow field distribution is not uniform, it will not only seriously affect denitration efficiency, increase ammonia escape, accelerate catalyst wear, but also block catalyst or cause blockage and serious corrosion of air preheater, Therefore, the simulation experiment of flow field is very important in the design of denitration system.

典型流場設計要求的反應器頂層催化劑層入口煙氣條件見表2, 如果要求脫硝效率達到85%以上, 則催化劑層入口的煙氣條件還要更嚴格。流場模擬試驗研究主要分為計算流體力學CFD計算與物理模型試驗驗證2部分。CFD計算更為關鍵的是計算模型的建立與邊界條件的設定,

The flue gas conditions at the top catalyst layer of typical flow field design are shown in Table 2. If denitrification efficiency is required to reach more than 85%, the flue gas conditions at the entrance of catalyst layer should be more strict. The flow field simulation experiment is divided into two parts: CFD calculation and physical model test verification. The most important thing in CFD calculation is the establishment of calculation model and setting of boundary conditions,

防止飛灰的沉積，定期對催化劑進行吹掃；控制好溫度，防止催化劑燒結；催化劑停用時要對催化劑進行保護。

Prevent the deposition of fly ash, purge the catalyst regularly; control the temperature to prevent the catalyst sintering; protect the catalyst when the catalyst is out of service.

更多的關于瓦斯發電機組的問題或者詳細的內容，請進入我們公司的網站：http://m.pyucoin.com 網站中會有很多的內容僅供參考。

For more questions or details about gas generating sets, please visit our company's website: http://m.pyucoin.com  There will be a lot of content in the website for reference only.